MINOLTA 7145 DRIVER

Enter the Crease mode and make a copy. This dipswitch is to adjust that shift. Parameter memory board 2 BK: OEM Products come with a manufacturer warranty only. This page contains information about installing the latest Konica Minolta driver downloads using the Konica Minolta Driver Update Tool. Once the shaft stopper fitting is removed, you must pull the cleaning rod out of the drum unit, and then unplug the connector from the drum unit. If the drum unit is in place at this time, the drum will rotate when you install or remove the drum rotating plate, resulting in possible damage to the cleaning

Uploader: Tygonris
Date Added: 5 September 2006
File Size: 30.8 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 45580
Price: Free* [*Free Regsitration Required]

Approximately lbs with DF provided Dimensions: Once warm-up has completed, the CB switches the L2 and the L3 minoltta and off so that the fixing heat roller can be maintained to the set temperature for idling.

RL1 the specified intervals. Page 29 List of major differences between the, and List of major differences between the, and Classification Reason Less than Warmup time Less than 19 sec.

DB drive board 9 pin 6 pin 19 pin. High-voltage exists around the drum mnolta. Move the lock lever [1] forward to release the lock, then pull out the ribbon cable [2]. Be sure to set the slit glass [2] so that a black dot on its side comes in the rear right side when you see the from the front side.

B5 – B5 Speaker F M1 Main motor speed abnor Konica Minolta brand copiers are renowned for their high reliability. The important maintenance parts for this machine are as described below Thus, you should switch the Konica Minolta Laser Printer off and unplug the power cord before proceeding with the drum replacement.

  ATAPI CD RRW 24X10 DRIVER

Konica Minolta 7145 Black OEM Developer (240 000 Yield)

Remove the developing unit from the main body. To adjust another adjustment item, press the arrow key to select the desired adjustment. This manual also for: Using the jig [1] included on the drum unit cover, rotate the drum clockwise and confirm that there are no gaps in the setting powder coat, and that the toner collection sheet and cleaning blade are smooth, etc. The procedure is as follows.

Next, you must pull the developing unit out of the printer, and then minnolta the ADU door. Table Of Contents List of major differences between the, and This page contains information about installing the latest Konica Minolta driver downloads using the Konica Minolta Driver Update Tool.

Konica Minolta 7145 Service Manual

Now, you must remove the drum unit jinolta pulling it gently towards you, and then remove the shaft stopper fitting of the cleaning rod. Finally, you must reset the drum count by selecting [Mode 25] — [2. Loosen the 2 screws [1] and remove the front cover [2] and the front door [3]. Don’t show me this message again. Hole Punch Operation S1: Fixing Temperature Control, Operation, Cleaning Web Control Once warm-up has completed, the CB switches the L2 and the L3 on and off so that the fixing heat roller can be maintained to the set temperature for idling.

  L755-S5246 TOUCHPAD DRIVER

After that, you must open the conveyance unit, and then loosen the fixing 745 of the drum unit.

KONICA MINOLTA SERVICE MANUAL Pdf Download.

After that, you must open the conveyance unit, and then loosen the fixing screw of the drum unit. In the first step of the replacement procedure, you must open the front door of your Konica Minolta Laser Printer, and then loosen the fixing screw of the developing unit.

Remove the 2 715 rings [1] and the bearing [2] on this side, and remove the paper feed roller unit [4] by sliding the bearing [3] on the rear side to the rear. You can immediately scan to email and scan to an FTP server.

Konica Paper Pickup Roller Tire.

When the value thus detected at this time is below the initial density recorded in the CPU contained in the CB Main body control boardthe M4 Toner supply motor 1 and the SD9 Toner solenoid are turned on to start to replenish toner up to the specified level of density.

Once the shaft stopper fitting is removed, you must mknolta the cleaning rod out of the drum unit, and then unplug the connector from the drum unit.